Victaulic TM-PFT510 Dokumentacja

HE.13987 WARNINGFailure to follow instructions and warnings could result in serious personal injury, property damage, and/or product damage.• Before

TOOL SETUP1. Insert the charged battery into the tool until it locks into position with an audible click.Reset Button2. Installation of the standard V

5. The red sliding collar must be adjusted to the proper operating position for the jaw size to be used. NOTE: If necessary, press the trigger to move

CAUTION• Keep fingers away from the locking pin/locking pin spring pinch point.Failure to follow this instruction could result in personal injury.7a

PRESSING OPERATION FOR ½-INCH/21.3-MM, ¾-INCH/ 26.9-MM, AND 1-INCH/33.7-MM SIZES WARNING• Before operating the PFT510 Vic-Press Schedule 10S Tool, re

Vic-Press Jaw CavitySeal Pocket Bead of FittingPipe Insertion Mark4. While positioning the standard Vic-Press jaw, make sure the pipe remains inserted

PRESSING OPERATION FOR 1 ½-INCH/48.3-MM AND 2-INCH/60.3-MM SIZES WARNING• Before operating the PFT510 Vic-Press Schedule 10S Tool, read the I-P500 F

4. Wrap the Vic-Press ring around the fitting so that the Vic-Press ring cavity aligns/engages with the seal pocket bead of the fitting. NOTE: The Vi

Hooks of Vic-Press AdapterJaw that Engage withVic-Press Ring6. Install the Vic-Press adapter jaw into the tool by following the “Tool Setup” section.6

8c. After the pressing operation is complete, release the Vic-Press adapter jaw from the Vic-Press ring by squeezing the levers. Remove the tool from

STANDARD VIC-PRESS JAW OR VIC-PRESS ADAPTER JAW REMOVAL WARNING• Use caution when releasing the locking pin. The locking pin is under spring-loaded p

INDEXHazard Identification ...1Operator Safety Instructions...2Introduction ...3Receiving The Too

WARNING• Wear safety glasses when working with compressed air to prevent debris from entering eyes.Failure to follow this instruction could result i

7. Use compressed air to remove any loose debris from the pressing cavities of the standard Vic-Press jaws and Vic-Press rings.8. Lubricate any pivot

TROUBLESHOOTINGPROBLEM POSSIBLE CAUSE SOLUTIONTool does not operate. The rechargeable battery is faulty or has completely lost its charge.Replace the

INDICATOR LIGHTS/SOUNDSOCCURS CAUSE OR RESULT20 SecondsAfter working cycle Low battery2 TimesAfter inserting the batterySelf check20 Sec/2 HzAfter wor

TM-PFT510_23TM-PFT510OPERATING AND MAINTENANCE INSTRUCTIONS MANUALwww.victaulic.comVICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY.REV_D

PFT510BATTERY-POWERED VIC-PRESS™ TOOL FOR VIC-PRESS SCHEDULE 10S SYSTEM PRODUCTSTM-PFT510OPERATING AND MAINTENANCE INSTRUCTIONS MANUALFor complete con

OPERATOR SAFETY INSTRUCTIONSUse of this tool requires dexterity and mechanical skills, as well as sound safety habits. Although this tool is manufactu

18. DO NOT ALTER THE PFT510 VIC-PRESS SCHEDULE 10S TOOL OR JAWS IN ANY WAY. Alterations to any tool components may result in improper product install

RECEIVING THE TOOLThe PFT510 tool, Vic-Press jaws, battery charger, and batteries are shipped in sturdy storage containers. Upon receipt of the tool,

USING THE DOLLY TO TRANSPORT THE TOOL OR ACCESSORY CASEDue to the weight of the tool and accessory cases, a dolly is provided for ease of transportati

BATTERY AND BATTERY CHARGER INFORMATION DANGER• Make sure the voltage on the battery charger’s label matches the voltage of the electrical source.Fai

TEMPERATURE REQUIREMENTS FOR CHARGING BATTERIESDo not charge batteries at ambient temperatures less than 50° F/10° C or greater than 104° F/ 40° C.TEM

RechargeableBatteryResetButtonTriggerLockingPinLevers of Standard Vic-Press JawSliding CollarEyelet for StrapButton for Sliding CollarBattery Release